MEP Filling Machine Parts and Manuals

St. Patrick's has been the EXCLUSIVE importer and authorized distributor of MEP in North America since 2003, over 21 years.

Use the schematics/manuals to identify parts. 
If the part you need is not listed on the page, then send an email. Include part number, photo, product serial number ....  Provide as much info as possible to help us get the part. 
Click Here for MEP Filler Manual
Click Here for Nozzle Schematic
Click Here for Nozzle Schematic 2008 and earlier

Wiring of Electronic level control.
Level Relay Com to Long rod in tank
Max to Short rod
Min to Middle rod
Sensitivity=2.5 kOhm, Mode=UP, Delay=Off

This is least sensitive setting and is good for wine. Products that have distilled water (some vodkas for example), may be better with increased sensitivity. Just try the unit first---if pump is not turning on/off as it should---increase the sensitivity.

If your product is pure distilled water, then even the most sensitive setting may result in intermittent operation. The easy fix for this is to bring the long and short threaded rods closer together. The easiest means is to put nuts on each of the rods. For example, put 2 nuts on the short threaded rod at the very bottom. Tighten them against each other. You need M6x1 metric nuts (at Home Depot ...)

If you have a filler with 110V pump, that is the Jet05.

swivelWheels-img
  $695.00

We sell this pump only as a replacement for MEP filler.

swivelWheels-img
  $70.00

2-3/16" x 1-3/16", 8 fins

swivelWheels-img
  $50.00
Pump Bearing 6202. Search for this on vxb.com
swivelWheels-img
  $130.00

Replacement. You must take the valve/push-in fitting off the old regulator and put on the new one.

  $15.00

3000 psi

swivelWheels-img
  $14.00

60 psi

swivelWheels-img
  $50.00

Attached to inlet of filling machine on older units.

No-return inlet, next item, can replace it.

swivelWheels-img
  $175.00

This is a new design of the inlet to the filler. It replaces the entire old inlet which included Rmp0812 (plastic inlet part) and the check valve.

swivelWheels-img
  $45.00

Stainless steel tube of the sparger, ~11" length.

swivelWheels-img
  $60.00

Solenoid valve for gas inlet of sparger

  $150.00

swivelWheels-img
  $90.00

White plastic rod that holds solenoid valve and sparger. It bolts to left side of filler.

swivelWheels-img
  $3.50

Nylon. 8 mm OD x 6 mm ID. Just push on.
You need 8' for all 4 nozzles.

swivelWheels-img
  $250.00
qty:
SOLD OUT

swivelWheels-img
  $250.00

If fill level of your bottle is greater than 3-1/4" below the top of the bottle, you will need this nozzle. If you are uncertain, please send us drawing of the bottle.

swivelWheels-img
  $250.00

Sold out. We will get them sent from MEP within ~3 weeks of order.

Nozzle Parts

swivelWheels-img
  $2.00

on tip of nozzle

swivelWheels-img
  $2.50

swivelWheels-img
  $2.00

swivelWheels-img
  $2.50

swivelWheels-img
  $2.50

swivelWheels-img
  $3.00

  $8.00

only on 2008 nozzle

swivelWheels-img
  $2.00

2005 and earlier filler

swivelWheels-img
  $28.00

Stainless steel tip

swivelWheels-img
  $15.00

swivelWheels-img
  $12.00

Do not overtighten set screw.

swivelWheels-img
  $85.00

swivelWheels-img
  $12.00

swivelWheels-img
  $23.00

swivelWheels-img
  $50.00

swivelWheels-img
  $42.00

same as tap0502 but for the long spirit nozzle

swivelWheels-img
  $2.00

 tip oring for mignon nozzle

swivelWheels-img
  $2.00

 oring at top where inner tube threads in.

swivelWheels-img
  $5.00

swivelWheels-img
  $12.00

Do not overtighten set screw.