Quick Instructions for Filling Machine. 1)Forget about the tray position. Adjust nozzle cone until fill level is correct. 2)Place tray at highest possible position.
MEP 4-spout electronic level control Filling Machine----2009 and later (best printed in color)
MEP filler earlier than 2009 is nearly identical except change in nozzle.
2009 and later nozzle schematic
2008 and earlier nozzle schematic
To correctly identify your nozzle, look carefully at Postition 8. On the newest nozzle, this is plastic plunger. On older nozzle, this is a stainless steel disc.
MEP 4-Spout Filling Machine Manual--older model, 2005 or ealier. Much different design.
Wiring of Electronic level control.
Level Relay Com to Long rod in tank
Max to Short rod
Min to Middle rod
Sensitivity=2.5 kOhm, Mode=UP, Delay=Off
[This is least sensitive setting and is good for wine. Products that have distilled water (some vodkas for example), may be better with increased sensitivity. Just try the unit first---if pump is not turning on/off as it should---increase the sensitivity.]
If your product is pure distilled water, then even the most sensitive setting may result in intermittent operation. The easy fix for this is to bring the long and short threaded rods closer together. The easiest means is to put nuts on each of the rods. For example, put 2 nuts on the short threaded rod at the very bottom. Tighten them against each other. You need M6x1 metric nuts (at Home Depot ...)
To switch transformer to 220 V, simply move the wire from 110 V to 220 V.
MEP-20 Pump 695 
We sell this pump only as a replacement for MEP fillers.
MEP-20 does not have a switch or cord.
If you have filler with 110V pump, that is the Jet05. go here for that.
230V, single phase, 0.75 HP, 60 Hz. 3.6 Amp. 930 rpm. 5.3 GPM. 1" TriClamp.
Impeller for MEP-20 Pump $60
2-3/16" x 1-3/16". 8 fins
MEP-20 Seals and Orings $50
pump Bearing 6202. search for this on vxb.com
Nitrogen Regulator $130
replacement for the filler. you must take the push-in valve off the old regulator and put on the new one.
High Pressure Gauge--N2 Regulator $15
3000 psi. Left hand thread
Low Pressure Gauge--N2 Regulator $14
60 psi. Left hand thread
Check Valve
We do not carry this item. No-return inlet, next item, replaces it.
Attached to inlet of filling machine on older units.
No-return inlet--complete setup $175
This is a new desgn of the inlet to the filler. It replaces the entire old inlet which included
Rmp0812 (plastic inlet part) and the check valve.
Sparging Arm for filler $45
This is the stainless steel tube of the sparger, ~11" length.
Also includes the stainless piece that it threads into.
Solenoid Valve for Filling Machine $60
This is solenoid valve for gas inlet. Electrical part only.
White Rod for sparger arm $90
Rmp1060. White plastic rod that holds solenoid valve and sparger. It bolts to left side of filler.
Tubing for Nozzle-to-Tank return $3.50/ft
Nylon. 8 mm OD x 6 mm ID. Just push on.
You need 8' for all 4 nozzles.
Nozzle Parts
Nozzles should be lubricated daily during use. Use Food Grade Silicone spray as a quick and easy lubrication. If you dissassemble to clean, then use heavier food grade lubricant such as petroleum jelly (vaseline) before reassembling. Nozzles operate better (easier without drips) and orings last much longer if lubricated routinely.
Use the schematics to identify your nozzle.
2037 Oring $2 each
Small oring on the tip of the nozzle.
115 Oring $2.50 each
(this is actually 3043 now.)
112 Oring $2 each
2068 Oring $2.50 each
1 of these and 1 3068 on newer nozzle. 2008 nozzle has 2 of these and no 3068.
3068 Oring $2.50 each
3131 Oring $3
There are two on a 4-spout MEP filler.
1016/1 Mad Gasket $8
only on 2008 nozzle.
108 Oring $2 each
from MEP filler of 2005 and earlier
Lower Seal Element , Rmp0507-1 $28
stainless steel tip
Rubber cone (14 mm ID) Rmp0105 $15 each
Conical seal element. Also replaces Rmp1005 on older fillers.
Adjusting Ring, Rmp0113 $12 each
Just snug up the set screw---overtightening damages ring and the pipe and is not needed.
Short Sliding Pipe Rmp0529 $75
includes the large diameter tube and the white plastic with nipple
Rmp0116 closing spring $12 each
Fixed Seal Element, Rmp0528-1 $23
Main Duct, Tap0502 $50
includes the small diameter tube and the elbow
Main Duct, Tap0502L-Long Nozzle $42
same as tap0502 but for the long spirit nozzle
Parts for Mignon Nozzles
2018 Oring $2 each
tip oring
2025 Oring $2 each sold out
oring at top where inner tube threads in
Rmp0533 rubber pad for mignon nozzle $5 each
Rmp0518 adjusting ring for mignon nozzle $12 each
Just snug up the set screw---overtightening damages ring and the pipe and is not needed.