Barrel Filler $95
304 Stainless steel. 1" diameter fill tube with silicone bung. 1.5" TriClamp inlet.

Long Fill Tube $20 in stock
24" Length. Unthread standard fill tube and replace with this to fill barrel from bottom up.

Barrel Topping Gun $79
304 polished stainless steel with 1/2" hose barb input.

Replacement Hat-shaped Rubber Gasket and S/S Washer $9 each
The Hat-shaped gasket should rarely wear out. Most failures are caused by loss of the stainless steel washer (between the plunger and the hat-gasket). If this washer is missing, the plunger can punch through the gasket.
Assembly order. Threaded cap-spring-hat gasket-washer-plunger.

Gas Racking Tool $125
304 Polished Stainless Steel. 1" TriClamp connection. 1/4" FPT Gas shutoff valve included. 1" stainless steel tube with adjustable bottom pin. Total length is 39"—works with burgundy or Bordeaux style barrels.

Gas Racking Tool with Standard Sight Glass $195
Gas Racking Tool with standard Sight Glass, clamp and gasket. Left photo.

Gas Racking Tool with Clear End Cap Window $176
Gas Racking Tool with Clear End Cap Window, Instrument Tee, 2 Clamps and 2 Gaskets. This unit weighs 2 lbs less than the Standard Sight Glass unit. Right photo.

Curved Racking Tube $49
1" polished 304 stainlesss steel curved tube with 1" TriClamp connection. Adjustable foot to stay above lees. Curved to allow insertion between barrel racks. Total length is 32".

Straight Racking Tube $49
Easier to use if you have only a single level of barrels. Total length is 32".

Barrel Cleaning Nozzle $49
304 Stainless Steel.
3/4" FPT.
Outside diameter 1.4"
Spins best in vertical position (either up or down).
Pressure/Flow: 20-40 psi and 8-15 GPM

Maintenance of all spray balls. Lubricate periodically with food grade silicone spray. Be sure to rinse well with water after cleaning. Always lubricate after cleaning.

Wand for Barrel Nozzle $24
3/4" pipe threads on both ends. Attach Barrel Cleaning Nozzle to short arm. 3/4" valve on other end. 304 polished stainless steel.

Barrel Cleaning Stand $295
304 stainless. Complete with Barrel Cleaning Nozzle, 3/4" FPT ball valve, TCx3/4" MPT adapters, TC clamps and gaskets. Modular design to allow easy modificaton.

TriClamp x 3/4" pipe thread--10" length $30

TriClamp x 3/4" pipe thread--7" length $28
304 polished stainless steel. 1" TriClamp. These are included with the Barrel Cleaning Stand.

Barrel Topping System $1045
St. Pat's topping system requires no special tools for maintenance and cleaning. Includes beer keg with 4" TriClamp opening and all parts and accessories. St. Pats custom fitting (4" Modified End Cap) allows pressurization, dispensing, and includes safety valve. Please note. [N₂ cylinder is NOT included. It is best to get a cylinder at your local gas supply.]
Complete with

• Topping Keg-4 (with 4" Modified End Cap)
• N₂ regulator
• Cart
• Topping Gun, tubing, clamps
• N₂ cylinder NOT included. This is provided by your local gas supply.

Barrel Topping System without Cart $470

Cart only $575
Entirely 304 stainless. 5" wheels, 2 swivel with brakes. Cylinder strap on center post (chain not shown in photo). 1.5" polished stainless steel handle, topping gun holder and hose brackets.
Inexpensive shipping via UPS.

N₂ Dual Gauge Regulator $65
Includes stopcock with check valve. 0-60 psi. 5/16" hose barb. This is also an Argon regulator (CGA580).

CO₂ Dual Gauge Regulator $60
Includes stopcock with check valve. 5/16" hose barb. Not used for cellar kegs but for P45 corker with gas purge. Also for beer dispensing

Topping Keg-4 $330 in stock
15.5 Gallon with large 4" TriClamp ferrule. Complete with modified end cap, clamp and gasket. The modified end cap has 5/16 ” hose barb for gas-in, 1/2” hose barb for wine out (Triclamp hose adapter--see photo), safety pressure relief valve, and stainless tube for wine pickup. 304 stainless with high-polish exterior.

Keg w/ 4" TC ferrule $200
15.5 Gallon with 4" TriClamp ferrule. You will need 4" End Cap, Gasket, and Clamp to seal off. 304 stainless with high-polish exterior.

4" Modified End Cap $130
4” TriClamp End Cap modified with 5/16 ” hose barb for Gas-In, 1/2” hose barb for wine out (Triclamp hose adapter--see photo), safety pressure relief valve, and stainless tube to draw wine from bottom of the keg, and 4” TriClamp gasket and 4” TC Clamp.

2" Modified End Cap $120
2" Modified End Cap will work on any American Sanke BEER keg (with the valve removed).
2" TriClamp End Cap modified with 5/16 " hose barb for Gas-In, 1/2" hose barb out (Triclamp hose adapter--see photo), safety pressure relief valve, and stainless tube to draw wine from bottom of the keg, and Sanke-TriClamp gasket and 2" TC Clamp.

Sanke-to-TriClamp Gasket $2
Modified 2" Silicone Gasket for using TriClamp fittings on standard Sanke beer kegs. [You do not need to weld a 2" TriClamp ferrule onto Sanke kegs to use TriClamp fittings.]

Beer Keg Tools
Components for Maintaining Sanke Beer Kegs
We do not sell standard beer kegs with Sanke valves.

The tools that you will need for maintenance of Sanke beer kegs are:

• Valve-Removal Tool. This tool is used to remove the valve for maintenance.
• Sanke Knives. These help remove the lock ring during valve removal.
• Keg Washer/Filler. This is used to clean the keg without removing the valve. Clean the keg between uses. You do not need to remove the valve each time you fill a keg.

Drop-In Valve-Removal Tool $75
304 stainless steel. For removing American Sanke (Type D) DROP-IN Valves.
This tool works only with Drop-In American Sanke. Sanke Knives are also needed with this tool.
Instructions for Drop-In Sanke Valve-Removal

3 Sanke Knives $30
Assists in removing the Lock Ring from American Sanke (Type D) DROP-IN Valves. Stainless steel blade.

'Beer Thread' Valve $30

• 304 stainless steel body
• Female 'beer thread' x Male 'beer thread'.

'Beer thread' (29/32"-14) is used on all keg couplers, European and American. All shanks for draft beer systems have 'beer thread' as well.

TriClamp x 'Beer Thread'
304 stainless.
'Beer Thread' is the thread that is on all keg couplers and shanks.

Female 'Beer Thread' x 1.5" TC $16

Male 'Beer Thread' 1.5" TC $17

Keg Washer and Filler $255
Filling: Keg is upright. Center port is fill port. Side port is vent.
Cleaning. Invert Keg. The Inlet is the center port. The outlet is the side port.

Includes Clean/Fill Coupler (See below), hose, fittings and clamps. Inlet Hose has 1.5" TriClamp. Can be used for hot caustic. Inlet hose is approved for high temperature (220° F) and pressure (300 psi). Hoses 3A approved. 6' inlet and 10' outlet hose.

Topping System without Keg/Cylinder (for Beer Keg) $210
Use with any American Sanke keg. 15' dispensing line and 5' gas line

Clean/Fill Coupler $170
Special Coupler for Cleaning or Filling beer kegs.

• Entirely stainless steel coupler (both probe and body)
• Inlet: TriClamp (A TriClamp x Beer Thread fitting is attached to the valve.)
• Outlet: 1/2" stainless steel hose nipple
• Stainless steel 'Beer Thread' valves on both inlet and outlet
• For use with American Sanke kegs only
• Cleaning. Invert the keg. The Inlet is the center port. The outlet is the side port.
• Filling: Keg in upright position. The Inlet is the center port. The vent is the side port.

Please note: The central component of the Clean/Fill Coupler is not the same as the Dispense Coupler. They appear very similar but they are not interchangeable.

Dispense Coupler $49
Used with the topping gun to dispense wine.

• Entirely stainless steel coupler (both body and probe, unlike 'wine couplers' which have stainless probe but chrome-plated brass body).
• 1/2" stainless steel hose nipple on Outlet.
• 5/16" hose nipple on Gas Inlet.
• For use with American Sanke kegs only
• Dispensing: The Gas Inlet is the side port. The Outlet is the center port.

Use of the Sanke Valve-Removal Tool and Sanke Knife
1. Tighten the Tool until pressure is released from the keg.
2. Use Sanke Knife to pull out the end of Lock Ring. Slide Knife around to remove Lock Ring.
3. Remove the Tool.
4. Remove the Sanke-valve from the keg. (Twist the Sanke-valve counterclockwise until the locking tabs align with the notches.)

To put the valve back in the keg:
1. Put in the Sanke-valve and twist clockwise.
2. Tighten Removal Tool. (Put Lock Ring under the Removal Tool first.)
3. Separate bottom end of the Lock Ring (use the Knife) and push into the groove. Use your fingers to push Lock Ring into the groove from the bottom end to the top end.
4. Remove the Tool.

Sanke Tool

Knife pulling out the top end of Lock Ring.

Knife removing the Lock Ring.

Sanke-Valve