EnoitaliaParts

Zambelli water presses--BP20/40/80/160/300/450

Bladder Press manual and schematic BP20,40,80
BP20/40/80 parts

Position 1--Air relief valve (1/4") $12
Position 2--Locking crank
for BP20 2008 and before $35
for BP20/40 $40
BP20 uses same locking crank as BP40 in 2009 and later
for BP80/160 $45
Position 22--Pressure gauge $20
note: this is same gauge on BP300/450 pos 36
Position 25---safety valve $50
4 bar for 20/40/300/450 liter presses.
Position 25---safety valve $50
3 bar for 80/160 liter presses.
Grommet Set (Positions 6,10,15)
6 and 10 are the same size. 15 is larger.
for BP20/40 $11
(20, 20, 21 mm)
for BP80/160 $19
(24, 24, 27 mm)

BP160 manual and schematic
BP160 parts

Position 73--Air relief valve (1/4") $12 sold out
same as on BP20/40/80
Position 15--Locking crank
for BP80/160 $45
Position 36--Pressure gauge $20
note: this is same gauge on all presses
Position 22---safety valve $50
3 bar for 80/160 liter press.
Grommet Set (Position 26 and unlabeled oring at bottom of shaft)
for BP160 $19
(24, 24, 27 mm---same as BP80)

BP300/450 Schematic
BP300/450 parts

Position 73--Air relief valve (3/8") $16
Position 36 --Pressure gauge $20
note: this is same gauge on all presses
Position 22---safety valve $50
4 bar for 20/40/300/450 presses
Position 76---Gasket (3 in set)
for BP300 $25 for set of 3 (33 mm)
for BP450 $35 for set of 3 (38 mm)

All Parts on this page MUST be ordered ONLINE--no phone orders If you do not see the part on this page, then send us an email.
Zambelli water presses--BP20/40/80/160/300/450 Bladder Press manual and schematic BP20,40,80 BP20/40/80 parts Position 1--Air relief valve (1/4") $12 Position 2--Locking crank for BP20 2008 and before $35 for BP20/40 $40 BP20 uses same locking crank as BP40 in 2009 and later for BP80/160 $45 Position 22--Pressure gauge $20 note: this is same gauge on BP300/450 pos 36 Position 25---safety valve $50 4 bar for 20/40/300/450 liter presses. Position 25---safety valve $50 3 bar for 80/160 liter presses. Grommet Set (Positions 6,10,15) 6 and 10 are the same size. 15 is larger. for BP20/40 $11 (20, 20, 21 mm) for BP80/160 $19 (24, 24, 27 mm) BP160 manual and schematic BP160 parts Position 73--Air relief valve (1/4") $12 sold out same as on BP20/40/80 Position 15--Locking crank for BP80/160 $45 Position 36--Pressure gauge $20 note: this is same gauge on all presses Position 22---safety valve $50 3 bar for 80/160 liter press. Grommet Set (Position 26 and unlabeled oring at bottom of shaft) for BP160 $19 (24, 24, 27 mm---same as BP80) BP300/450 Schematic BP300/450 parts Position 73--Air relief valve (3/8") $16 Position 36 --Pressure gauge $20 note: this is same gauge on all presses Position 22---safety valve $50 4 bar for 20/40/300/450 presses Position 76---Gasket (3 in set) for BP300 $25 for set of 3 (33 mm) for BP450 $35 for set of 3 (38 mm)	Wooden Water Press parts Manuals for wood-cage water presses 2009 and later (Marchisio) 2008 and earlier (Enorossi) Special Note on BP150-W membrane. The membrane for orginal BP150-W (Enorossi) is different than now (mfg is Marchisio). Large opening on one end of bladder is different. Membrane for Marchisio has ~3.5" opening. Membrane for Enorossi has larger ~5.5" opening. Please note that there were minor changes in the wood cage water presses beginning in 2009. The parts below are the same for all years. BP320-W, BP150-W, and BP80E-S/S Air Valve 1/8" $14 Air valve is same on all units. Pressure Gauge $31 Pressure gauge is same on all units. Oring for BP320 (700 diameter) $5 Pos 28, 10010605 (53.34x5.34) Oring for BP150 (500/550 diameter) $4 Pos 7, 10010604 (44.45x3.53) Oring for BP80E-SS (400/450 diameter) $4 Pos 8, 10010603 (32.92x3.53)	Zambelli Hydraulic Presses Oil for hydraulic press. ISO 32 (aka SAE 10) weight hydraulic oil. Grainger carries Mobil DTE 24 but Shell or other brands are fine. This is the same oil used in the vacuum pump of corking machines. Motorized Hydraulic Press Manual Manual Hydraulic Press Manual Additional information for hydraulic press Run capacitor for Tio-70. 230 V, 40 microfarad $35 Apple Shredder Video of 16 gallon Apple Crusher in use (4.6 MB) Apple Shredder Manual Replacement blades $100 complete with P/Ns 2,3,4,5 For MuliMAX 60L (16 gallon) hopper Pneumatic Capper Pneumatic Capper Manual. 28.5 NI/min = 1 scfm Oring/Gasket set for piston $20 2 each of P/N 2/3 (large oring), 1 each of P/N 2/5 (orange). Push-In Fitting P/N 4/6 $6 1/4" tube x 1/8"male 90° elbow
	Ratchet Presses Ratchet Press Instructions, and Ratchet Press schematic Shieves (position number 4 in the Schematic) Shieve for RP40/50 $8 each Shieve for RP55 $10 each Shieve for RP70 $12 each
	Zambelli Peristaltic Pump Vacuum Connect compressor to IN. Do NOT exceed 3.8 bar (55 psi). Start Pump first, then introduce the compressor. The vacuum is created inside the housing.	Instructions for Cleaning the pump head or replacing the impeller of the Zambelli T/25.