Enolmatic/Enolmaster Parts MUST be ordered online.
We do not accept phone orders for Enolmatic parts.

Service questions for Enolmatic MUST be initiated via email. Please read the info below to troubleshoot the Enolmatic and Tandem filter. If you still have trouble, send an email with the problem.

Replacement Parts for Enolmatic/Enolmaster
St. Pat's is the largest Tenco distributor in USA and the leading supplier of parts, and unfortunately, perhaps the only supplier of parts in USA. In order to support the Enolmatic and Enolmaster, we maintain an inventory of the most commonly replaced parts. St. Pat's is the largest Tenco distributor in USA and the leading supplier of parts, and unfortunately, perhaps the only supplier of parts in USA.

Please use the schematics to identify the part by NUMBER.

• Enolmatic Manual, and Schematic of Enolmatic and Schematic of Enolmatic Motor/Parts (this schematic is not in your enolmatic manual).
• Enolmatic Filter Instructions and Filter Housing parts schematic
• Enolmaster Manual
• Enolmaster Filter parts schematic
• Enolmaster/Enolmatic Filter Housing Instructions. Place filter(s) in housing and attach hoses. Open small bypass valve on top of filter housing. Turn on unit and fill bottles until filter housing fills with liquid. Now close bypass valve on top of filter housing and product will be filtered.

Trouble shooting Enolmatic and Filter (or Enolmaster and Filter)
If you are using the Filter Housing and are having trouble, disconnect the filter and use the Enolmatic alone. Be sure the Enolmatic is okay before proceeding to testing the filter. Then read the Tandem Instructions above to trouble shoot the filter.
If the Enolmatic will not fill, check the suction at every connection point beginning with the black tubing (vacuum valve to vessel). Just follow the vacuum flow to the nozzle. You must have a bottle under the nozzle to check the vacuum on the inlet side of the nozzle.

Clogged Vacuum line on Enolmatic
It is common, if you bottle sweet wines or liqueurs, for the line between the vacuum pump and vacuum-adjustment valve to get plugged. The blockage, crystallized sugar, is usually at the small valve. It is quite easy to clean this with a small wire or pipe cleaner. Clients who use Enolmatics for sweet liqueurs clean this routinely.

If you need a part that is not listed below, check if it is a component of an assembly below. You must purchase the entire assembly.
If the part is not listed below and is not part of a larger assembly below, we can have it sent by airfreight from the manufacturer but the cost is typically $50-$100 for shipping alone.

Enolmatic Nozzle Parts
1011 Complete Nozzle $55 (406,202,206,420,408,203,410,422,409,807,403,204)
1020 Complete Nozzle with Levers and Spring $65 (1011,103,411,412,421)
420 Silicone Cone for Wine Nozzle (red or white color) $7 each
202SIL Red Silicone End Oring $.50 each
206 White Silicone Pre-End oring $.50 each
203 Silicone gasket $2.50 each
403L Nozzle stem $20 each
410 Gasket Bushing $2.50 each
422L (may be 422 in schematic) Spring $5
406 Nozzle End Piece $5.00 each
....Note on removing 406 nozzle end piece: Turn 180° and then pull out.

810 Mignon Nozzle End Gasket $6

436 Lever Knob $4 each
437 Lever Closing Roller $4 each

To completely dissassemble Enolmatic nozzle.
Use needle nose pliers. Turn nozzle end piece (part 4.06) 180°, and then pull out. This requires a good bit of force. The remaining components are easy to disassemble.
Put a little lubricant on orings and gaskets when reassembling. (Pam, vegetable oil, or vaseline are fine).
To reassemble, nozzle end piece 4.06 must be pressed firmly into the outer tube.

other Enolmatic parts
416 Gear Stop $1 each
402 Rack Guide $6 each
1007 Gear unit $14 each
301 Switch and Cap $9

Enomatic Vessel and parts
1006 Complete Vessel Cover and Float (includes vessel cover oring and 419,205,407,201,427,418) $35
Float for vessel cover (205+419+418+427) $27
415 Enolmatic Vessel $35
201PP Vessel Cover oring (134-4) NBR $4

Enolmatic Tubing
512 10.5 mm ID Soft tubing for Enolmatic $2 per foot
511 Black Vacuum tubing $3
514 clear vacuum tubing $3
1001 (430+801+428+801+429) Complete Set of Rigid Suction Pipes $14 out-of-stock

Enomatic Clamp
812 Clamp that secues Enolmatic to counter top $9

Tubing for DemiJohn and 5-10 liter bottle kit
This tubing is supplied with the demijohn and 5/10 liter bottle kits.
6.36 mm ID tubing $1.75 per foot

Enolmatic Vacuum Pump and parts
524UL/USA Complete Vacuum Pump P15 110 V 60 Hz $170
787026 Cylinder P15 $8 o/s
787022 gasket $6 o/s
787022 gasket $6 o/s
048022 pump connecting rod o/s
707040 90° Connection P15 $3
707002 90° Connection P15 $4
790000 P15 Muffler with connection $14
787085 P15 Pump Head $14

Tandem Housing Parts
1023 Complete Cover for Tandem Filter Housing $70 (includes 425, 215, 1025 and cover)
215 Filter cap oring silicone $9
425 Filter cap oring holder $11
1025 90° bypass valve $30 (the male nipple on 1023 cannot be broken to use this)

EnolMASTER Nozzle Parts
Some parts are the same as in the Enolmatic nozzle--see above.
P/N 1022 Stainless Steel Nozzle for Enolmaster $325
..........Complete with nozzle, levers, spring.
Enolmaster Nozzle diagram
Parts unique to the Enolmaster nozzle
Position 3 is 457-E Ecopur Lip Gasket for S/S nozzle (this replaces P/N 457) $19
Position 4 is 458 Holding Bushing for S/S Nozzle $24
These parts are also used on Enolmatic nozzle.
Position 1 is 420 Silicone Cone $7 each
Position 5 is 202SIL Red Silicone End Oring $.50 each
Position 6 is 206 White Silicone Pre-End oring $.50 each
Position 19 is 459 Black Washer NBR $1.00
Position 19X is 459X White Washer nylon $1.00

Enolmaster tubing
10.5 mm ID Soft tubing (into nozzle) $2 per foot
6.36 mm ID tubing (top of nozzle to cylinder) $1.75 per foot
MA606 Vacuum pump to Cylinder tubing (8.5x13 mm) $13
Large tubing 1" Pliovic $1.90 per foot

other Enolmaster parts
MA1033 Enolmaster Motor Filter $225
This can be used when bottling very high alcohol products to protect the vacuum pump from alcohol vapors. See page 10 of the Enolmaster manual. You need white mineral oil (or some equivalent with no smell). Change oil after ~250 gallons of bottling.
MA524USA complete Enolmaster vacuum pump $675
MA510 200x190x295 Enolmaster cylinder only $80
...(This is clear plastic cylinder in Enolmaster. Note it is NOT the same cylinder in the filter housing.

Enolmaster vessel FLOAT (MA531float+205 oring +MA532 knob) $28

MA511 200x190x265 filter housing cylinder only $85 out of stock
This is clear plastic cylinder in Professional Filter housing for Enolmaster. Note it is NOT the same cylinder in the Enolmaster itself.

Enolmater for High Temperature Liquids and/or for High Alcohol >50%
Standard Enolmatic can handle 80° C. Temperature limit is 120° C with this tubing and Pyrex vessel. . You need 7' of 566 tubing, 4' of 565 tubing, and 7+' of MA609 (to reach your tank).
P/N 566 tubing (6 mm ID) for Nozzle to Vessel $3.75/foot
P/N 565 tubing (10 mm ID) for Nozzle to Manifold $4.50/foot
P/N MA609 tubing (25 mm ID) for Manifold to your tank $9 /foot
MA1020Pyrex complete Enolmaster pyrex vessel without cover $450 o/s

Enolmatic is CSA NRTL/C certified. This is a certification that assures that the machine is manifactured with respect of the safety regulamentation of U.S.A. and Canada. UL is the most popular certification but the meaning is the same (download pdf for more info).