All Parts on this page MUST be ordered ONLINE--no phone orders

If you do not see the part on this page, then send us an email.

• Pumps
• Elevator and Sorting Tables
• Destemmer/Crushers

All Parts on this page MUST be ordered ONLINE--no phone orders

Euro 20 Manual (best in color)
Euro 30 Manual (best in color)

Euro 20 parts
Euro 20 schematic
Orings (position 2--2 pieces) for Euro 20 $8
Seal (position 9 in schematic) $35

Capacitors changed at beginning of 2012. It is easy to determine which version you have by position of the start switch.

2011 and earlier: Start switch is on the top of the electrical box.
2011 Run Capacitor (~10 uF) $20
2011 Start Capacitor (~40 uF) $24

2012: Start switch is on the side of the electrical box.
2012 Run Capacitor (~14 uF)$?
2012 Start Capacitor (~50 uF Xenon) $?

Euro 30 single speed parts
We have sold two versions of Euro 30 single speed since 2002.
How to tell New from Old Euro 30 Single speed.
Measure diameter of the small oring (or the oring groove)
50 mm (almost 2") is New (see pos. 7 in Euro 30 New Schematic)
40 mm (1-9/16") is Old.

• Wheel. $10
  5" diameter, 16 mm ID.
• Motor $280
  230 V, single phase, capacitor start.
• Oring Set for Older Euro 30 Single Speed $12
  2 each of 2151, 80x2.5
  1 each of 3143. Small oring is 40 mm.
• Seals for OLD Euro 30 Single Speed $25
  2 parts. 20x42x7 and 20x35x7
  
• Oring Set for NEW Euro 30 Single Speed $12
  2 ech of 2151, 80x2.5 (pos. 6,13)
  1 ech of 3187. Small oring is 50 mm. (pos. 7)
  
• Seals for New Euro 30 Single Speed $25
  2 parts. Pos. 8 and 9 in Schematic. 20 mm.
• Bypass Oring $2
  There are two set screws holding the bypass.
• Start Capacitor for Euro 30 single speed $24
• Black Run Capacitor for Euro 30 single speed $20
  Older models may not have start cap. If you have a 3-position switch (not 5) then you have only a run capacitor.
• Switch for Euro 30 with start capacitor $55
  ?? Check model number with client.
• Switch for Euro 30 without start capacitor $50
  CA0120034R03 Check model number with client. Pumps sold ~2002/03

Euro 40-FD manual (best in color)
Euro 50-FD manual (best in color)
Euro 60-FD manual (best in color)
Euro 60-FD-D (dry run protection) manual (best in color)

Euro 40-FD (MVE) parts

• Motor for Euro 40-FD $520
  with separate fan. Seals and flange included. You need the Orings.
• Seals $25
  Pos. 8 and 9. 20 mm
• Orings $15
  2154, 3193, 2154. Pos. 6,7,13.

Euro 50-FD (MVE) parts

• Motor for Euro 50-FD $610
  with separate fan. Seals and flange included. You need the Orings.
• Seals $40
  Pos. 8 and 9. 25 mm
• Orings $18
  2157, 3212, 2157. Pos. 6,7,13.

Euro 60-FD (MVE) parts

• Motor for Euro-60-FD $700
  with separate fan. Seals and flange included. You need the Orings.
• Seals $30
  Pos. 8 and 9. 30 mm
• Orings $20
  2164, 3256, 2164. Pos. 6,7,13. [typo in schematic. Pos. 13 is 2164, not 2154.]

Complete Remote $220
Remote without cable $110
yellow handle with potentiometer, switch, ... (requires soldering)
Potentiometer for remote $15
includes dial. Soldering required.

The replacement motors for Euro 40/50/60-FD have separate fan. If you have a pump with a separate fan, then hookup is obvious.

If you have an older pump that does not have a separate fan [Does the motor fan run when you turn on the main power? --If no, then you have a unit without separate fan.], then you need to run two wires from the control box to the motor. 1)Run the two hot wires from either the outlet side of the fuse box (labeled 2 and 4) or the inputs to the frequency drive. 2)Get an electrical bulkhead and install it thru the wall of the control box. 3)Pull the fan wires out of the motor box. Connect the hots to fan wires. Be sure to seal up the opening on the motor electircal box with silicone.

Wheels and Tires for Euro 40/50/60 carts.
Pneumatic tires for pumps after 2009/10.
(outer) Tire only $20
Inner-Tube only $10

Wheel for pumps before 2009/10. $15
Hard wheel on pumps sold prior to 2009/10. ~8" diameter. 20 mm ID. same wheel on larger destemmers.

Enoitalia Elliptical Rotor Pump Manual
Simalube Grease $100
info on Simalube gas-injected lubricant for Elliptical rotor pump. SL10-125 (tube filled with food grade grease)

Gear box oil is either Shell Tivela S320 or Shell Omala 220

Enoitalia pump with TIMER instructions

• Wiring
• Electric Motor Repair
• Changing Orings and Pump Seals
  
  

Euro 30 MVI
Euro 30 MVI has same seals and orings as NEW Euro 30 single speed.
Euro 30MVI and Euro 60MVI transmission manual including type of oil
Euro 30 MVI (Long shaft) schematic
Euro 30 MVI (short shaft) schematic

• Wheel. $15
  ~8" diameter. 20 mm ID. same wheel on larger destemmers.
• Oring Set for Euro 30 MVI $12
  2 ech of 2151, 80x2.5 (pos. 6,13)
  1 ech of 3187. Small oring is 50 mm. (pos. 7)
  
• Seals for Euro 30 MVI $25
  2 parts. Pos. 8 and 9 in Schematic. 20 mm.
• Bypass Oring $2
  There are two set screws holding the bypass.
• Switch $60
  CS0160052 (confirm with client before shipping)
• Transmission (motovariator) for Euro 30 MVI $850 in stock
• Motor for Euro 30 MVI 230V, 60 Hz, single phase. $290 in stock

Euro 60 MVI
Euro 30MVI and Euro 60MVI transmission manual including type of oil
Euro 60 MVI (Long shaft) schematic
Euro 60 MVI (short shaft) schematic

• Hydraulic transmission with flange (motovariator) $1700 out of stock
  Transmission with long 5.5" black flange and shaft extension. This can replace transmissions in older models that had short 2.5" black flange. The transmission has shorter shafte than original, so you must have the extension and longer flange as well. Must also reuse the grey flange (between transmission and black flange) of old pump.
• Hydraulic transmission (motovariator) $1500 out of stock
  This is transmission only. It can replace transmission in either of the units pictured above.
• Motor 3-phase, 230 V $300

TC3600 Elevator/Sorting Table Manual and Tension Adjustment Instructions

SC2500/3000/3500 belt elevator manual

U200 Screw Elevator

some other dimensions of SC3000.
at 50°, unloading 2190 mm, loading 480/310 mm, elevator 2700Hx2050L
at 45 °, unloading 2030 mm, loading 560/390 mm, elevator 2600Hx2200L
at 40 °, unloading 1860 mm, loading 640/470 mm, elevator 2450Hx2300L
at 35 °, unloading 1680 mm, loading 710/540 mm, elevator 2300Hx2450L

Do NOT pressure-wash gears, chains, and bearings. There is rarely any reason to wash these components. Sealed bearings will be destroyed if pressure washed.

Do not pressure wash or hose down motors or electrical components.

Lubricate moving components after each season and during the season if needed.

Do NOT use Metabisulfite/citric acid. It is an ineffective sanitizer and is corrosive to stainless steel. This solution will corrode holes in tanks, filling machines, and destroy seals and bearings in pumps, if left in contact for extended period or allowed to dry without effective rinsing. It is used only in the wine industry---never in dairy, beer, or other food industries. Metabisulfite has another use in the winery, which apparently lead to its misuse as a sanitizer.

Pressure washers have destroyed the following items in the past 2 seasons.

• Motor on pumps
• Bearings on destemmers.
• Electronics on pumps and membrane press
• Rubber bladder on membrane press
• Electronics on labeler
• Electronics on filling machine

Sealed bearings cannot withstand pressure washers.
NEMA 4 enclosures cannot withstand pressure washers.

Adjusting the rollers on Eno-15, ENO-3.
The gap between roller axles (4a and 4b) is changed by turning nut (1).
In addition, the bolt/nut (3) is in a slot such that when a stone enters between the rollers, roller 4a can move to the left against the tension of the spring (2).
Nut 3 should not be tightened down (It is a nylon self-locking nut so it will not come loose.)

Click here for schematic of ENO 15 parts
Eno 15 manual

• Position 4 $10
  Pulley for motor. 19 mm ID, x68 mm
• Position 11. $20
  Bearing 6204 2RS. 20 mm ID, 47 mm OD, 14 mm thick.
• Position 15. $13
  Support. 20 mm ID. (S20). Lubricate annually.
• Position 21. $30
  Support for rollers.
• Position 24. $21
  same as Position 25 but an extra hole is drilled for slotted pin. Note user can replace slotted pin with small nut/bolt. This is for units with rubber rollers.
• Position 25. $21
  Gear on drive roller. ID=18 mm. OD=96 mm (3.8") 16 teeth. This is for units with rubber rollers.
  
• Position 26. $32
  Sprocket (corona). ID= 18 mm. Outside diameter is ~10.4". 64 teeth.
• Position 30. $5
  gasket. same as position 4 of Jolly 35.
• Position 31. $25
  top gear. 20 mm ID. 25 teeth.
• 110V Motor $175
  same motor on ENO-3M/10/15. Motor does not include pulley or baseplate.
• Capacitor for Eno-15/10 o/s
  31.5 microF, 2-5/8" long.
  

Click here for schematic of Eno 10 parts
Eno 10 manual

• Position 4. $5
  gasket G15. same as position 4 of Jolly 35.
• Position 5. $13
  same as position 15 on ENO-15. Lubricate annually.
• Position 7 $10
  Pulley for motor. same as pos. 4 of ENO-15
• Position 10. $20
  same as position 11 bearing on ENO-15
• Position 13. $31
  Large Sprocket . 20 mm ID.
• 110V Motor $175
  same motor on ENO-3M/10/15. Motor does not include pulley or baseplate.
• Capacitor for Eno-15/10 o/s
  31.5 microF, 2-5/8" long.

Click here for schematic of Eno-3 parts

• Position 4 $10
  Pulley for motor. same as pos. 4 of ENO-15
• Position 11. $20
  same as position 11 bearing on ENO-15
• Position 15. $13
  same as position 15 on ENO-15. Lubricate annually.
• Position 21. $30
  same as position 21 of ENO-15.
• Position 24.
  Same as Position 24 on ENO-15. This is for units with rubber rollers.
• Position 25.
  Same as Position 25 on ENO-15. This is for units with rubber rollers.
  [Note that pos. 24/25 for Eno-3 with rubber rollers are not the same as pos 24/25 for units with nylon or aluminum rollers. If you have a unit with nylon or aluminum rollers, please note this in the order and we will sub the appropriate part.]
• Position 26. $30
  Sprocket (corona). ID= 18 mm. Outside diameter is ~8.3". 50 teeth.
• Position 32. $11
  S1041 support. Lubricate annually.
• Position 33. $10
  S1010 support. Lubricate annually.
• 110V Motor $175
  same motor on ENO-3M/10/15. Motor does not include pulley or baseplate.
• Capacitor for Eno-15/10/3 o/s
  31.5 microF, 2-5/8" long.

Click here for schematic of Jolly 35 destemmer and Manual for Jolly 35

• Position 1. $14
  Support S25 .25 mm ID. Does NOT have brass insert.
• Position 4. $5
  Foam Gasket G15.
• Position 5. $45
  Large Gear. 25 mm ID. OD ~ 14".
• Position 15 $21
  Bearing. 6205-2RS. 25 mm x 52 mm x 15 mm.
• Position 17 $26
  Gear. 25 mm ID. OD ~ 2.75". 18 teeth.
• Position 23 $50
  Impeller. 25 mm ID. takes 8 mm slotted pin (or use bolt).
• Position 27 $14
  Gasket for pump
• Position 29. $11
  Oil seal. 35x52x7
• Position 35. $20
  Support with brass insert. 25 mm ID
• Jolly 30/35/40 wheel. $10
  16 mm ID. ~5.75" OD.
• 230V, Single phase motor for Jolly 30/35/40/50 single speed $350
  Same motor as Jolly 50 single speed. Please measure shaft diameter and send this info with your order. You may also need a new pulley if shaft diameter is different.
• Capacitors for single phase motors---see Jolly 30 A/R parts

Click here for schematic of Jolly-30-A/R parts
Manual for Jolly 30 A/R

• Position 2. $20
  Support with brass insert. 25 m ID. Same as position Pos. 35 of Jolly-35.
• Position 4. $5
  Gasket G15. same as position 4 of Jolly-35.
• Position 5-1. $14
  Support S25. 25 mm ID. Does NOT have brass insert. same as Position 1 of Jolly-35. Note schematic is incorrect. There are two S20 and one S25, not three S25. S20s support the rubber rollers. S25 supports the hopper auger.
• Postion 5-2. $13
  Support S20. same as Position 15 of Eno-15. Note schematic is wrong. There are two S20 and one S25, not three S25. S20s support the rubber rollers. S25 supports the hopper auger.
• Position 6.
  sprocket included with Position 14.
• Position 8. $60
  large gear. 20 mm ID, OD~14". [Note this is NOT same as position 5 of Jolly 35. ID is 20 mm, not 25 mm.]
• Position 10. $30
  Support for rollers. same as position 21 of Eno-15.
• Pos. 13. $18
  Gear. 20 mm ID. ~4" diameter. 16 teeth.
• Position 14. $26
  Gear. 20 mm ID. ~4" diameter. 16 teeth. Includes sprocket (Position 6).
• Position 25 $21
  Bearing. Same as position 15 of Jolly 35.
• Position 27 $26
  Same as Pos. 17 of Jolly 35.
• Position 32. $50
  Impeller. same as Jolly 35 Pos. 23.
• Position 33. $14
  Gasket. same as Jolly 35 Pos. 27.
• Position 38. $11
  Oil seal. same as Jolly 35, pos. 29.
• Jolly 30/35/40 wheel. $10
  16 mm ID. ~5.75" OD.
• 230V, Single phase motor for Jolly 30/35/40/50 single speed $350
  Same motor as Jolly 50 single speed. Please measure shaft diameter and send this info with your order. You may also need a new pulley if shaft diameter is different.
• Start BLACK Capacitor---Outside-$25
  with leads for capacitor mounted on side of motor. ~125 microF
• Start BLACK Capacitor-Inside $20
  without leads for capacitor mounted inside electrical box. ~125 microF
• Run GREY Capacitor--Outside -$15
  with long leads for capacitor mounted on side of motor. 25-35 microF
• Run GREY Capacitor--Inside-$12
  with short leads for capacitor mounted inside electrical box. 30 microF
  

Click here for schematic of Jolly 40-A/R parts
Manual for Jolly 40 A/R

• Pos. 4. $45
  Large gear. 25 mm ID. Same as pos. 5 of Jolly-35.
• Pos. 5. $20
  Support with brass insert. 25 mm ID. same as Pos. 35 of Jolly-35.
• Pos. 6. $5
  Gasket G15. Same as pos. 4 of Jolly-35.
• Pos. 26 $26
  Gear. 25 mm ID. OD ~ 2.75". 18 teeth. Same as Pos. 17 of Jolly 35.
• Pos. 32. $30
  Large sprocket. ~10" OD, 25 mm ID.
• Pos. 34. $18
  same as Pos. 13 of Jolly 30 A/R
• Position 35. $26
  same as Pos. 14 of Jolly 30 A/R
• Jolly 30/35/40 wheel. $10
  16 mm ID. ~5.75" OD.
  
• Jolly 40/50/60 Front caster. $18
  [wheel diameter is ~4" (100 mm). Total height with caster is ~5"]
• 230V, Single phase motor for Jolly 30/35/40/50 single speed $350
  Same motor as Jolly 50 single speed. Please measure shaft diameter and send this info with your order. You may also need a new pulley if shaft diameter is different. We no longer sell Jolly 40 single speed.
  (If you have Jolly 40 with variable speed, this is NOT the motor.)
• Capacitors for single phase motors---see Jolly 30 A/R parts
• 3-phase motor for Jolly 40/50/60 variable speed $350
  This is the correct motor if you have Jolly 40 variable speed--with inverter box.

Click here for schematic of Jolly 60 parts and manual and St. Pats manual

• Jolly 50/60 Rear Wheel. $15
  ~8" diameter. 20 mm ID.
• Jolly 40/50/60 Front caster. $18
  [wheel diameter is ~4" (100 mm). Total height with caster is ~5"]
• Position 5. $21
  Bearing. same as Pos. 15 of Jolly-35. 6205-2RS. 25 mm x 52 mm x 15 mm.
• Position 10. $45
  large gear. same as Pos. 5 of Jolly-35. 25 mm ID. 100 teeth. ~14" diameter.
• Pos. 11. $14
  S25 support. 25 mm ID. same as Pos. 1 of Jolly-35.
• Pos. 12. $5
  gasket G15. same as pos. 4 of Jolly-35.
• Pos. 14 $25
  UC206 bearing in F206 housing. 30 mm ID. Housing fixed with 4 bolt holes. same as pos. 24 of Jolly 50 A/R
• Pos. 24. $11
  oil seal. 40x65x10
• Pos. 25 $25
  same as Pos. 44 of Jolly 50 A/R
• Pos. 39 $25
  same as pos. 24 of Jolly 50 A/R
• Pos. 40 $25
  SB205 bearing in FL205 housing. 25 mm ID. Fixed with 2 bolts. same as pos. 26 of Jolly 50 A/R
• Pos. 50. $43
  roller gear. 30 mm ID. ~6-3/4" OD. 15 teeth.
  
• Pos. 51 $25
  same as Position 24 of Jolly 50 A/R
• Moeller VFD for Jolly 50/60 $700
  Variable freq dirve only---not control box.
• 3-phase motor for Jolly 40/50/60 $350
  Use only with VFD (variable speed)

click here for Jolly 50 A/R schematic
and Enoitalia manual
and St. Pats manual

Jolly 50 uses many of the same parts as Jolly 60.

• Jolly 50/60 Rear Wheel. $15
  ~8" diameter. 20 mm ID.
• Jolly 40/50/60 Front caster. $18
  [wheel diameter is ~4" (100 mm). Total height with caster is ~5"]
• Position 5. $21
  Bearing. same as Pos. 15 of Jolly-35. 6205-2RS. 25 mm x 52 mm x 15 mm.
• Position 10. $45
  large gear. same as Pos. 5 of Jolly-35. 25 mm ID. 100 teeth. ~14" diameter.
• Pos. 11. $14
  S25 support. 25 mm ID. same as Pos. 1 of Jolly-35.
• Pos. 12. $5
  gasket G15. same as pos. 4 of Jolly-35.
• Pos. 24 $25
  UC206 bearing in F206 housing. 30 mm ID. Housing fixed with 4 bolt holes.
• Pos. 26 $25
  SB205 bearing in FL205 housing. 25 mm ID. Fixed with 2 bolts.
• Pos. 27 $11
  oil seal. 25x62x10
• Pos. 29 $25
  same as Pos. 24
• Pos. 35 $11
  same as Pos. 27
• Pos. 36 $25
  same as Pos. 24
• Pos. 37 $25
  same as Pos. 26
• Pos. 40. $95
  Gear on drive roller. 15 teeth. 25 mm ID. ~6-3/4" OD. this also has the small steel sprocket attached.
• Pos. 44 $25
  UC206 Bearing in FA206 housing. 30 mm ID. One side fixed, the other side adjustable.
• Position 46 $15
  Pulley for motor. Double belt. 28 mm ID, 86 mm OD
• Pos. 48. $42
  gear on other roller. 15 teeth. 20 mm ID. ~6-3/4" OD
• Pos. 51. $8
  Handwheel---adjusts roller spacing
• Pos. 55 $25
  same as Pos. 44
• Pos. 69. $11
  oil seal. 40x65x10
• Moeller VFD for Jolly 50/60 $700
  DF51-322-2K2 Variable freq dirve only---not control box.
• Moeller Relay ESR4-NO31-230VAC $245
• LED M22-LED230 $20
• 3-phase motor for Jolly 40/50/60 $350
  Use only with VFD (variable speed)
• 230V, Single phase motor for Jolly 50 single speed $350
  We no longer sell single speed Jolly 50. If you have Jolly 50 with variable speed, this is NOT the motor.

Jolly 100 manual
Jolly 100 Parts
parts below are in stock but please consult before ordering

• Pos 43
• Pos 44
• Pos 52
• Pos 53
• Pos 57

Destemmer/crushers that we no longer offer.

Jolly 50 destemmer with built in must pump.
Pos. 46B. Must pump bearing. SB205 in FL205 housing. 25 mm ID.

Jolly 20 A/R parts --most parts are the same as those on Jolly 30 A/R

Eno 20 parts -- many parts are the same as on ENO-15

Trouble Shooting the Inverter Control for Jolly 50/60
Never get control panels wet. Remove the control box before cleaning. Never wet down a motor. Never use a pressure washer on bearings.

To make testing easier, we recommend connecting the 2 wires going to the interlock (i.e., override the interlock). Simply remove the 2 wires from the connector on the control box, and use a wire nut to tie them together. This eliminates the possibility of a faulty interlock being the source of a problem.

1. Be sure you have power to box. Be sure Emergency Stop button is pulled out. Should be 1/4" yellow between black ring and red top.
2. Remove cover from inverter box.
3. Turn power on (from "0" to "1"). Inverter (Moeller DF51-322-2K2) display should come on. If it does not, then test for 230 V going into the inverter.
4. Also, power (yellow) light on the yellow Moeller relay (ESR4-NO31-230VAC) should be on. If not, check the fuses next to the relay.
5. Push Blue button on panel and turn Stop-Start switch to Start. The K1/K2 light on Moeller relay should come on and the Blue light should be on. If K1/K2 is on but not blue light, the blue LED (M22-LED230) is burned out. If the K1/K2 did not light up, then the relay is probably bad.
6. Turn speed control dial (0-10) up and motor should turn. You can test without the motor but you must get Moeller Inverter to display "d001". If it is not displaying this, then press <PRG>, then press <up arrow> or <down arrow> until you get to d001. Now press <PRG> and it will display the output frequency. Adjust the speed contrl dial (0-10) on the control panel of the box, and the output frequency will change from 0-60 Hz.

Jolly 50/60 Inverter box plugs

Weidmuller 1652420000 Outside bracket with metal clip $30
1652380000 Inside part $20

1 1498100000 4-pin Male for motor $15
1 1498200000 4-pin Female for motor $15

1 1498300000 5-pin Male for interlock $15
1 1498400000 5-pin Female for interlock $15